Conference Papers

Permanent URI for this communityhttp://197.211.34.35:4000/handle/123456789/2

Conference Papers

Browse

Start date: 2011End date: 2019

Search Results

Now showing 1 - 10 of 30
  • No Thumbnail Available
    Item
    Approaches to Security of Information Resources in Academic Libraries in Niger State, Nigeria
    (Samaru Journal of Information Studies, 2018-04-16) Fati Abubakar & Dr. B. S. Aduku
    This study examines approaches to security of information resources in academic libraries in Niger State. Three research objectives were framed for the study. The case study design was adopted for the study, and purposive sampling technique was used to select 35 respondents from a population of 297 staff in all the 12 academic libraries in Niger State. Semi structured interview guides were used to collect data from respondents, while field notes guide were used to record data in respect of participants’ observation. The data collected were subjected to qualitative analysis. The findings revealed that: the common approaches adopted for the security of information resources included periodic random checks on users and staff, scheduled patrols, and checking of users IDs, while computers of some libraries had antivirus software installed, and passwords configured. However, surveillance cameras were functional in only one library. The prevalent threats in all the libraries included book theft, mutilation of information resources, and non-return of borrowed library materials, impersonation, and computer virus attack. The 12 libraries had policies guiding the security of information resources, but they did not have insurance cover. It was concluded that although academic libraries in Niger State have adopted good approaches for securing their information resources. The fact that they paid more emphasis on printed materials, with less use of electronic security systems, it is obvious that the libraries were yet to embrace the opportunities offered by technological advancement for such activities. In view of the findings, it was recommended that libraries should endeavour to have written policies on all aspects of security of information resources, while efforts should be made to improve the qualities of such materials that have already been degraded or replace them if necessary. Finally, it would be necessary to enhance the manual methods of safeguarding library materials, while emphasis should gradually shift to the electronic methods.
  • No Thumbnail Available
    Item
    Delaying transition in a Blasius boundary layer with finite compliant panels
    (Fourth International Symposium on Bifurcations and Instabilities in Fluid Dynamics (BIFD),, 2011-07-18) Bori Ige; Zhao, .X.; Yeo, .K. S.
    Compliant surfaces have been shown to be a promising passive control measure for controlling and delaying boundary layer transition in various theoretical studies [1-2]. In this paper, we report on a recent study we have done on the evolution of pulse-initiated disturbance wavepackets over one or more finite-length compliant panels. The broadband nature of a wavepacket offers a central advantage in permitting natural selection of most dominant waves to operate through the sum of its growth processes. This may be helpful in identifying the critical waves and key processes that are involved at the various stages in natural transition. The initiation, evolution and final breakdown of wavepackets into the incipient turbulent spots in a Blasius boundary layer was modelled by Direct Numerical Simulation (DNS) briefly described in [3]. The comparative evolution and transition performance of three cases are discussed here, namely the rigid-wall case, a single-panel wall and a two-panel wall. In all cases, a fixed vertical-directed delta pulse of small amplitude was initiated at the point x /  349.4, where   2.3182103m is the displacement thickness of the boundary layer at the initiation point. The evolution and breakdown of the wavepacket in a Blasius boundary layer on a rigid wall has already been reported in [3]. For the single-panel case, a finite section of the wall from x /  450 to 762 was replaced by a tensioned membrane on a viscoelastic foundation, whose properties were designed to inhibit the development of compliant-wall modes. The simulation results showed that, the upstream intervention by the finite compliant panel effectively delayed the onset of the incipient turbulent spot by a distance of about 100 cm ( x /  430). This represents an approximately 30% increase in the transition distance measured from the point of wavepacket initiation. Spectral study indicated that the relatively short membrane panel was able to effectively attenuate the primary 2-D Tollmien-Schlichting (TS) wave mode so that resultant wavepacket after the panel was dominated by a pair of oblique waves. Subharmonic secondary instabilities [4-5], which are responsible for nonlinear disturbance wave amplification on a rigid wall, were thus inhibited by the absence or near absence of the 2-D TS wave mode. Staggered Λ-structures and streamwise streaky structures similar to those found in the rigid wall case were observed for the single-panel case, but much further downstream. A second tensioned membrane panel of the same length was added at x /  1359-1658 to form the two-panel case. The last stage of the present simulation shows the wavepacket arriving the location x /  2000 in a perfectly laminar form ( max | u | /U 0.05   ) – this already represents an increase in transition distance of about 50% over the corresponding rigid-wall case. The eventual breakdown location will be further downstream as the wavepacket has not displayed the usual structural features that signify imminent breakdown. This study has shown the efficacy of short compliant panel(s) in controlling and delaying transition.
  • No Thumbnail Available
    Item
    Evolution of wavepacket over short compliant panels in a Blasius boundary layer
    (American Physical Society (APS), 65th Annual Meeting Division of Fluid Dynamics (DFD), 2012-11-18) Bori Ige; Yeo, .K. S.; Dou, .H-S.
    Compliant surface has been proved in various theoretical studies as a promising tool in delaying transition. This study concerns our recent work carried on the evolution of pulse-initiated disturbance wavepackets over finite-length compliant panels in a Blasius boundary layer by direct numerical simulation (DNS) method. A finite section of the wall was replaced by a tensioned membrane on a damped foundation. By comparing with the rigid wall case, the upstream intervention by a finite compliant panel was found to effectively delay the onset of the incipient turbulent spot – an increase of about 40% in the transition distance with respect to the initiation point was obtained. Transition distance to the occurrence of the incipient turbulent spot was increased further to about 75% relative to a rigid wall when a second compliant panel was introduced. Spectral analysis shows the important role of the fundamental 2D modes in wavepacket evolution and the roles played by compliant panels in transition delay.
  • No Thumbnail Available
    Item
    DEVELOPMENT OF A BRAKE DRUM MODEL WITH FINS INCORPORATION FOR HEAT DISSIPATION ENHANCEMENT
    (5th Multi-disciplinary academic conference, Ahmadu Bello University, Zaria. January 11, 2018. Pp. 190 – 205., 2018-01-11) Bako, .S.; Bori Ige
    Extreme heat within an automobile brake drum could cause brake failure which could as well lead to death of passengers and lost of properties. One of the ways to dissipate heat faster from an automobile brake drum is by incorporating fin on the outer surface of the brake drum as pointed out in many literatures. This work concerns converting 1/10 0f the overall height thickness of the brake drum into fins for effective heat dissipation by both conduction and convection. During the modified brake drum development process, necessary fin design formulae were taken into account. Modeling and simulation analysis were carried out using Solidworks (2013) software, followed by validation using theoretical Finite Element analysis. The minimum temperatures obtained from the simulation analysis were 4935K and 4927K for the existing and the modified brake drum model respectively. While maximum displacements obtained from the simulation analysis were 5142×10−5𝑚𝑚 and 5102×10−5𝑚𝑚 for the existing and the modified brake drum model respectively. This implies that the modified brake drum have improved strength and better heat dissipation than the existing model. This is as the result of the circumferential arrangement of the fins on the outer surface of the brake drum.
  • No Thumbnail Available
    Item
    Delaying transition further with the aid of a short compliant panel in a Blasius boundary layer flow
    (The Chinese Society of Theoretical and Applied Mechanics (CSTAM), Fluid Mechanics Division Conference, Guilin, China., 2012-11-12) Bori Ige; Yeo, .K. S.; Dou, .H-S.; Zhao, .X.
    The cost of fuelling especially for those in the transport industries could be reduced drastically if there is a means of reducing drag force over their vehicles while in motion. One way to overcome this is to use compliant (membrane) surface; a passive control means which has been proved in various theoretical studies as a promising tool in delaying transition further. In this paper, following the earlier work done on flow over rigid wall within a Blasius boundary layer, we account for the current study carried out on the evolution of pulse-initiated disturbance wavepackets over a finite-length compliant panel by direct numerical simulation (DNS) method. For the single-panel case, a finite section of the wall from X = x/δ0 = 450 -762, was replaced by a tensioned membrane on a viscoelastic foundation, whose properties were designed to inhibit the development of compliant-wall modes. Where δ0 is the displacement thickness at the perturbation location. A small amplitude vertical initiating delta pulse was introduced from the wall streamwise location X0 = 349.4 (x0 = 81cm), and study in detail both spatially and spectrally how the wavepackets generated evolve from the initiating point to the breakdown location over a Blasius boundary layer. The simulation results showed that, the upstream intervention by the finite compliant panel effectively delayed the onset of the incipient turbulent spot by a further distance of Δx = 550, when compared with the rigid wall case results that earlier broke down at X = 1420. This represents an approximately 51% increase in the transition distance measured from the point of wavepacket initiation. Spectral study indicated that the relatively short compliant panel was able to effectively weaken the primary 2-D Tollmien-Schlichting (TS) wave mode, thereby extending the linear regime, so that resultant wavepacket after the panel is dominated by two oblique wave modes and this is the effective strategy of transition delay.
  • No Thumbnail Available
    Item
    Development of Screw-Type Briquetting Machine for Municipal Solid Waste
    (2nd International Engineering Conference (IEC 2017) Federal University of Technology, Minna, Nigeria, 2017-10-17) Okegbile, .O. J.; Bori Ige; Danlami, .S. M.
    The Hydra headed problem of deforestation and Municipal Solid Waste (MSW) Management has bedeviled Nigerian States. Deforestation has put Nigeria on the world’s map as the highest contributor to the world’s deforestation of its primary forest (contributing over 50%), as over 70% of its population depends on firewood and charcoal for cooking and heating. The rising profile of MSW, characterized by inefficient management methods make most Nigerian cities an eye sore, with uncollected waste littering almost every available space, drainages and water channels which poses great danger to human existence. Without alternative energy source available to the growing population, deforestation will continue unabated and in the nearest future Nigeria risk losing all of its forest resource. A Screw-Type briquetting machine was developed that utilizes crushed, combustible MSW to form briquettes to be used for cooking and heating, which is using one problem to fix another. MSW was formulated, crushed and used to form briquette. The briquettes produced burn in similar way to charcoal when compared. This will reduce to the barest minimum, deforestation rate and improve the management of MSW by utilizing as a resource what is termed waste. The developed machine has a throughput capacity of 2605.4Kg/hr and is driven by a 5 Horsepower (5 hp) electric motor.
  • No Thumbnail Available
    Item
    An Investigation On Ventilation and Air Conditioning (VAC) Installation, Design and Performances of Selected Buildings in Ilorin, Kwara State, Nigeria
    (2nd International Engineering Conference (IEC 2017) Federal University of Technology, Minna, Nigeria, 2017-10-17) Yusuf, .A. W.; Bori Ige; Nasir, .A.
    time. Heating, ventilation and air-conditioning (HVAC) play an important role in providing a comfortable condition for occupants in a building. This work concerns air conditioning designs, installations, and performances of some event centres namely: Banquet Hall, Atlantic Event Centre and Nimatoni Event Centre and some offices within the Kwara State Ministry of Water Resources. The impact of the effect of improper design and ventilation on energy efficiency and consumption were also considered. The event centres and offices were studied, by taking both the temperature and relative humidity values for over a period ranging from 75 minutes to 130 minutes, with the use of a device referred to as HOBOware temperature/relative humidity data logger coupled with a HOBOware Software interface installed on a personal computer, for post processing of acquired data. The obtained results of the event centres showed variations in the capacities of the installed air-condition understudied. Also from the results obtained, the cubic meter per minute (cmm) values were found to be 0.0896, 0.2908 and 0.0404 for Banquet hall, Atlantic Event Centre and Nimatoni Event Centre respectively, and these were below the standard recommended value of 0.4245 in the literature.
  • No Thumbnail Available
    Item
    Formation of Ceiling Boards by the Combination of Sugarcane Bagasse and Rice Husk
    (International conference on global & emerging trends, Baze University, Abuja, Nigeria. 2 - 4 May, 2018. Pp. 140 – 143., 2018-05-02) Jesuloluwa, .S. I.; Bori Ige
    Constructing housing components from agricultural wastes have become a special area of research in engineering. Hence a lot of resources is pushed into this to obtain sustainable, eco-friendly and low-cost houses. This work studies some properties of ceiling boards produced from sugarcane bagasse and rice husk. The ceiling boards were produced using water, cement as binder with binder composite ratio of 3:2 by weight, sugarcane bagasse and rice husk of varying ratios by weight from 100% of bagasse to 0% of it with a 25% decrease. The compression of the boards was done manually using moulded block as weight. From the results, it was observed that the ceiling board produced with 100% sugarcane bagasse has better properties to be considered for ceiling board as compared with the most commonly used ceiling boards like Plaster of Paris(POP), asbestos and Poly Vinyl Chloride(PVC). The properties examined are thermal conductivity, thermal resistivity, water absorption and density. The better ceiling board has thermal conductivity to be 2.27W/mK, thermal resistivity of 0.441 mK/W, water absorption of 16.89 and density of 470.3 kg/m3.
  • No Thumbnail Available
    Item
    Development of Footstep Electricity Energy Generating Machine using Dual Generator
    (Alex Ekwueme Federal University, Ndufu-Alike Ikwo, Ebonyi State, Nigeria, 2019-05-15) Igbo, .E. B.; Bori Ige
    Footstep electricity energy generation machine have been seen in most populated country and the different existing machines have various capacity of generated electricity power. The concept and the technology is simply the production of electrical energy by weight which acts on the footsteps. Footstep electrical energy generation is of three types namely; rack and pinion, piezoelectric method, fuel and piston method. It was comparatively discovered that the rack and pinion mechanism is more effective, efficient with less cost of operation and maintenance. In the existing rack and pinion method, energy was not adequately harvested from footsteps as a result of many gears, shafts and incorporation of a single generator. This takes time to generate electricity and the output capacity is low in watt. With this motivation, a prototype footstep electricity energy generating machine using dual generators, chains and sprockets was developed. This was designed by considering parameters such as human weights, speed and low cost. The prototype was designed to be a value for money production in the power generation sectors. For designing the work rack and pinion, human weight were studies to understand the operation. At the end, the machine was fabricated using local material. The machine upon fabrication was evaluated at ten (10) different human weights of 40, 50, 53, 56, 60, 70, 85, 101, 105, 108 kgs and power of 6.69, 6.949, 3.92, 10.848, 8.29, 8.339, 12. 064, 11.349, 11. 359 and 11.359 watts, with angular speeds of 5.08, 5.28, 2.98, 8.24, 6.30, 6.33, 9.16, 8.62, 8.63, 9.35 rpm were obtained respectively. The result showed that weight is directly proportional to both power and angular speed. The result showed that optimism occurred at 85kg. Using a dual generators increase higher electricity energy generation, effective and efficient harvesting of footstep energy.
  • No Thumbnail Available
    Item
    Application of Inverse method to Reconstruct the form of Pulse During Impulsive damage to Pipelines
    (International Engineering Conference (IEC), 2015) O. A. Olugboji; J. Hale; J. Y. Jiya; C. K. Jack
    Petroleum pipelines damages if untimely detected, poses a tremendous challenge to the oil sector of an economy as it causes oil spillage, theft or explosion of the petroleum products while on transit. It is against this backlash an inverse pulse propagation method for reconstructing the form of pulse generated during pipeline defects was devised and presented in this paper. Inverse problem occurs in several branches of science and engineering. It involves the determination of the parameters of a model that describes or explains a set of observed data .This work deals with an inversion technique that was developed to reconstruct the form of a pulse after it has been propagated along a pipe. To test the suitability of the developed technique, a mathematical model was developed. The theoretical model was validated by experiment using a developed pipeline system. The experimental test rig comprises of a flexible hose pipe 23m long and 19mm diameter with four pressure sensors distributed along the pipeline and connected to the data acquisition system. Static and flowing air in the pipeline were use in the experimental test to validate the developed inverse technique model. The inverse method showed a close relationship to the original pulse.